We have RSR/MTS/MTRR/MTRG/MTRH/MTRF/MJSR series roots blower,Super quality tri-lobes high rotary speed industrial electric blower,three lobe roots blower， roots vacuum pumps and the related products, which is widely used in sewage treatment, chemical plant, MVR project, cement plant, electric power plant, fertilizer plant, paper producing, coal mill, textile mill, food plant, aquaculture, vacuum package, metallurgy industry and many other industrial,three lobe roots blower
GGHGA
i,Super quality tri-lobes high rotary speed industrial electric blower Low noise
three lobe roots blower with adoption of helical tri-lobe roots rotors and the discharge port of special geometry, the airflow noise is much lower compared to typical straight-lobe roots blower. The noise level can be reduced by 8db in the band of low frequency; hence the noise in the surroundings of blower can be significantly improved.
HDHSD
ii, Super quality tri-lobes high rotary speed industrial electric blower High adiabatic efficiency
three lobe roots blower with design of helical tri-lobe roots rotors, the airflow pulsation is less and the air streamline would be more stable. Therefore the fluctuation in airflow is less and then the energy waste can be reduced.
SSFFS
iii, Super quality tri-lobes high rotary speed industrial electric blower Super Energy saving
three lobe roots blower Compared to the typical roots blower under the same operation conditions of discharge pressure and airflow volume, the power consumption of helical tri-lobe roots blower will be lower by 20.
OASAD
Super quality tri-lobes high rotary speed industrial electric blower
Product DescriptionMTS Series Roots Blower Specification
Specification of MTS Series Roots Blower
1.All models of MTS series
MTS-11 MTS-12 MTS-21 MTS-22 MTS-23 MTS-31 MTS-32 MTS-33 MTS-41 MTS-42
2.Size of Discharge Bore
65(2.5″),80(3.15″),100(4″),150(6″),200(7.8″),250(9.85″)
Or in customer’s indication range
3.Differential pressure scope
19.6—98kPa
4.Air capacity scope
3.94—119 m3/min
5.Power of the motor
3—200kW
NECESSARY STANDARD ACCESSORIES
Tuyere take over;entrance&exiting silencer(with air filter);flexible connector;check valve;foundation bolt;deflating valve;pressure gauge;base;gear oil
MTS Series Roots Blower Technical Parameter
Roots Blower Production Processing
A:Machine Casing Machining Component
Machine Blank-production&testing - Rough milling - Finish milling - Bore hole -drilling&tapping -Testing -Stock
B:Lobes Machining Component:
Machine Blank-Production&Testing-Lathe Facing&reaming hole-rough plane-finish plane-
semi finished products -shaft installation-make static&dynamic balance
C:Drive/Driven Shafts Machining Component:
Steel rod testing -cutting -Heat treatment -Bore Holes-Lathing smoothing-install shaft into the lobes-testing-stock.
D: Wall Plate Machining Component:
Plate Blank production - plate wall milling - bore holes -testing -stock
Company Information
Company Information
Workshop Showing
Advance Equipment Showing
Payment terms,Packaging and Shipping
A. Our payment terms is mainly choice T/T,L/C or other terms you are convenient.
B. Our package including two methods: standard exported wooden box and iron box.
C. Our transportation: by sea, air or railway transportation.
Certifications
Certifications
(1).A Roots blower case with low noise
(2).A composite wire rotor of three-lobe Roots blower
(3).A high negative pressure Roots Super quality tri-lobes high rotary speed industrial electric blower pump
(4).Super quality tri-lobes high rotary speed industrial electric blower pump case(high negative pressure)
(5).A high pressure air-cooling Roots blower
(6).A photoelectric dividing apparatus of three-lobe rotor
(7).Back flow pressure relief valve
(8).Roots blower(high pressure air-cooling)
(9).A Roots blower with cooling tank without leakage
(10).A Roots steam compressor
(11).A steam compressor with mechanical seal
(12).A mechanical-sealed steam compressor’s circulating water system for cooling
(13).A steam compressor’s wallboard
(14).Intelligent monitoring system of Roots blower
FAQ
Q1: How about the price?
A: The price is negotiable. It can be changed according to your quantity or packaging.When you are making an inquiry, please let us know the quantity you want.
Q2: How about the after-sales service?
A: We provide 1 year's guarantee, installation guide, and life-long free technical consulting.
Q3: How about the OEM?
A: Welcome, you can send your own design of blower product and LOGO, we can open new mold and print or emboss any LOGO for you.
For more detailed information , hope you could finish below form or click "chat now" for online service on the right side.